Stage 09: First Print

Written By: Makertech 3D
  • Comments: 5
  • Favorites: 0

Difficulty

Moderate

Steps

14

Time Required

Suggest a time??

Sections

1

Flags

0

  1. Download the new v5.2.1 of Makertech Cura for windows here.

    • Download the new v5.2.1 of Makertech Cura for windows here.

    • Run through the install and setup wizards.

    • If you have an earlier version of Makertech Cura installed, delete it from your programme folder before installing the new one.

    Edit

    • If you are running Mac OS or Linux the 3.5 profiles will be made available in the next release of the official Ultimaker Cura.

    • Follow the progress of this request here.

    Edit

  3. Our first print will be the 3D Benchy.

    • Our first print will be the 3D Benchy.

    • Click here to download the STL file.

    Edit

  4. In Cura add the Proforge 3 3D printer.

    • In Cura add the Proforge 3 3D printer.

    Edit

  5. Under the Travel dropdown adjust the retraction setting to 0.2mm for the direct drive extruder.

    • Under the Travel dropdown adjust the retraction setting to 0.2mm for the direct drive extruder.

    Edit

  6. Click here to load the Benchy STL that you downloaded earlier.

    • Click here to load the Benchy STL that you downloaded earlier.

    Edit

  7. Set the correct nozzle size and material for your set-up. The default profiles give you a good starting point, these will need to be edited to get the best results out of your material, this can be done by going into the custom settings.

    • Set the correct nozzle size and material for your set-up.

    • The default profiles give you a good starting point, these will need to be edited to get the best results out of your material, this can be done by going into the custom settings.

    Edit

  8. Once happy, hit slice and save the gcode to your SD card.

    • Once happy, hit slice and save the gcode to your SD card.

    Edit

  9. Fix the spool holder assembly to the side of the printer:

    • Fix the spool holder assembly to the side of the printer:

    • M5 x 100mm Bolt

    • M5 Penny Washer

    • M5 T-Nut

    Edit

  10. Use a pair of scissors or side cutters to cut a sharp point to your filament. Place the spool onto the spool holder and feed the filament through the filament sensor and up to the extruder. Put pressure on the extruder idler arm and continue to feed the filament into the hotend.

    • Use a pair of scissors or side cutters to cut a sharp point to your filament.

    • Place the spool onto the spool holder and feed the filament through the filament sensor and up to the extruder.

    • Put pressure on the extruder idler arm and continue to feed the filament into the hotend.

    Edit

  11. Pre-heat the hotend and heated bed. Remember that the bed is measuring the temperature of the heater, the platform still requires a few minutes to uniformly reach that temperature. Remember that the bed is measuring the temperature of the heater, the platform still requires a few minutes to uniformly reach that temperature.

    • Pre-heat the hotend and heated bed.

    • Remember that the bed is measuring the temperature of the heater, the platform still requires a few minutes to uniformly reach that temperature.

    Edit

  12. From the home screen go to Print -> TFT SD -> P3_3DBenchy.gcode From the home screen go to Print -> TFT SD -> P3_3DBenchy.gcode From the home screen go to Print -> TFT SD -> P3_3DBenchy.gcode

    • From the home screen go to Print -> TFT SD -> P3_3DBenchy.gcode

    Edit

  13. Once the print begins, you can monitor/adjust it from the print menu. Make sure that you have a good first layer, this is key to a good print. If it's too close (the nozzle is scraping the bed) or too high (the first layer is peeling away) adjust your P offset. See the previous guide for a reminder on how to do that.

    • Once the print begins, you can monitor/adjust it from the print menu.

    • Make sure that you have a good first layer, this is key to a good print.

    • If it's too close (the nozzle is scraping the bed) or too high (the first layer is peeling away) adjust your P offset. See the previous guide for a reminder on how to do that.

    • Keep monitoring your print.

    Edit

    After a long pause, the bed shuts down...

    when it resumes, the bed does not come up again..

    it is printed in the air...

    Markus - Reply

    Sorry to hear this, if you’ve not already, could you please email us directly at info@makertceh3d.com with more info/video of the issue, so we can better assist.

    Makertech 3D -

  14. Your Proforge 3 is successfully up and running!

    • Your Proforge 3 is successfully up and running!

    Edit

    I have very bad multiple prints during the flow and retraction tuning process. (5 benchy, 6 retraction towers, 2 3D test V3. All strange results) all done with Esun PLA+.

    Some are saying in the forum, bad under extrusion. Is there any optimised setup in cura that I should try?

    Christopher - Reply

    If you find you’re getting a lot of jamming, we recommend reducing the retraction and the hotend temperature.

    Makertech 3D -

Finish Line

Author

Makertech 3D

Member since: 03/09/2018

35,630 Reputation

96 Guides authored

One Comment

Which setting in CURA must be used. I used the default setting but the layers don't stick to each other. The printer is otherwise set up and calibrated correctly. The first layer sticks well. What do I have to change?

Hermann Dengler - Reply

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 16

All Time: 497