You're viewing a previously published revision of this guide. View latest revision

May 03, 2020 - 10:05:09

Jan 05, 2021 - 09:01:11 Aug 23, 2020 - 05:08:28 Aug 14, 2020 - 05:08:44 Aug 13, 2020 - 06:08:40 Aug 13, 2020 - 06:08:18 Aug 10, 2020 - 09:08:39 Aug 08, 2020 - 11:08:05 Aug 08, 2020 - 11:08:46 Jul 30, 2020 - 03:07:57 Jul 28, 2020 - 12:07:23 Jul 11, 2020 - 10:07:26 May 28, 2020 - 07:05:52 May 28, 2020 - 07:05:57 May 28, 2020 - 07:05:02 May 28, 2020 - 07:05:08 May 07, 2020 - 09:05:11 May 07, 2020 - 09:05:03 May 07, 2020 - 09:05:24 May 07, 2020 - 09:05:44 May 07, 2020 - 09:05:37 May 07, 2020 - 09:05:22 May 07, 2020 - 09:05:06 May 07, 2020 - 09:05:24 May 07, 2020 - 09:05:16 May 03, 2020 - 12:05:01 May 03, 2020 - 12:05:35 May 03, 2020 - 12:05:21 May 03, 2020 - 11:05:26 May 03, 2020 - 11:05:43 May 03, 2020 - 11:05:36 May 03, 2020 - 11:05:59 May 03, 2020 - 11:05:46 May 03, 2020 - 11:05:48 May 03, 2020 - 11:05:03 May 03, 2020 - 11:05:18 May 03, 2020 - 11:05:17 May 03, 2020 - 11:05:45 May 03, 2020 - 11:05:38 May 03, 2020 - 10:05:49 May 03, 2020 - 10:05:50 May 03, 2020 - 10:05:04 May 03, 2020 - 10:05:09 May 03, 2020 - 10:05:36 May 03, 2020 - 10:05:04 May 03, 2020 - 07:05:38 May 03, 2020 - 07:05:36 May 03, 2020 - 07:05:42 May 03, 2020 - 07:05:04 May 03, 2020 - 07:05:44 May 03, 2020 - 07:05:41 May 03, 2020 - 06:05:46 May 03, 2020 - 06:05:47 May 03, 2020 - 06:05:59

Newer

Stage 1: Base

Written By: Makertech 3D

Comments: 28
Favorites: 0
Completions: 28

Difficulty

Easy

Steps

Time Required

00:30:00 - 01:00:00

Step 1 X-Motor

Fix one of the NEMA 17 motors to the base like shown.

Fix one of the NEMA 17 motors to the base like shown.
Nema 17 motor
M3 x 6mm
The cable connector should to be facing upwards.

Step 2 Z-Motor and Z-Pillar

Align the Z-Pillar to the base like shown in the first image.

Align a Motor underneath it also with the connector pointing upwards.

Fix everything together with four M3 x 6mm bolts.

Align the Z-Pillar to the base like shown in the first image.
Align a Motor underneath it also with the connector pointing upwards.
Fix everything together with four M3 x 6mm bolts.

Step 3 Z-Pillar Support

Take the Z-Pillar and align it into position with the base assembly.

Fix the top of the support pillar to the main pillar with two M4x10mm bolts and M4 nyloc nuts.

Take the Z-Pillar and align it into position with the base assembly.
Fix the top of the support pillar to the main pillar with two M4x10mm bolts and M4 nyloc nuts.
M4 x 10mm bolt
M4 Nyloc Nut

Step 4 Z-Pillar Support to Base

Fix the support pillar to the base.
M4 x 10mm bolt
M4 nyloc nut

Step 5 Electronics Fan

Fix the 40mm electronics fan onto the side of the base.

Fix the 40mm electronics fan onto the side of the base.
M3 x 16mm bolt
M3 nyloc
Ensure that the sticker side is facing into the base.

Step 6 X-Endstop

Fix the X-Endstop (it is the one with the shorter cable) to the inside of the base.

Fix the X-Endstop (it is the one with the shorter cable) to the inside of the base.
M2.5mm bolt
M2.5 nyloc nut
Make sure that the switch's lever is pointing towards the back of the base.