You're viewing a previously published revision of this guide.  View latest revision

Older
Mar 11, 2022 - 05:03:31
Apr 15, 2022 - 07:04:56 Apr 15, 2022 - 06:04:01 Apr 11, 2022 - 02:04:30 Apr 11, 2022 - 02:04:21 Apr 02, 2022 - 05:04:17 Apr 02, 2022 - 05:04:57 Mar 19, 2022 - 07:03:40 Mar 19, 2022 - 07:03:17 Mar 19, 2022 - 07:03:14 Mar 19, 2022 - 07:03:03 Mar 18, 2022 - 07:03:14 Mar 16, 2022 - 11:03:17 Mar 16, 2022 - 02:03:16 Mar 14, 2022 - 08:03:20 Mar 14, 2022 - 07:03:08 Mar 14, 2022 - 07:03:24 Mar 14, 2022 - 07:03:34 Mar 14, 2022 - 07:03:08 Mar 14, 2022 - 07:03:42 Mar 14, 2022 - 07:03:14 Mar 14, 2022 - 07:03:37 Mar 14, 2022 - 07:03:58 Mar 13, 2022 - 07:03:09 Mar 13, 2022 - 07:03:00 Mar 13, 2022 - 07:03:50 Mar 13, 2022 - 07:03:13 Mar 13, 2022 - 07:03:47 Mar 13, 2022 - 07:03:30 Mar 12, 2022 - 07:03:24 Mar 12, 2022 - 05:03:08 Mar 12, 2022 - 05:03:04 Mar 11, 2022 - 08:03:53 Mar 11, 2022 - 07:03:20 Mar 11, 2022 - 07:03:04 Mar 11, 2022 - 07:03:50 Mar 11, 2022 - 07:03:42 Mar 11, 2022 - 07:03:02 Mar 11, 2022 - 07:03:29 Mar 11, 2022 - 07:03:48 Mar 11, 2022 - 07:03:50 Mar 11, 2022 - 07:03:30 Mar 11, 2022 - 07:03:40 Mar 11, 2022 - 07:03:40 Mar 11, 2022 - 07:03:38 Mar 11, 2022 - 07:03:30 Mar 11, 2022 - 07:03:21 Mar 11, 2022 - 05:03:16 Mar 11, 2022 - 05:03:05 Mar 11, 2022 - 05:03:12 Mar 11, 2022 - 05:03:21 Mar 11, 2022 - 05:03:02 Mar 11, 2022 - 05:03:04 Mar 11, 2022 - 05:03:31 Mar 11, 2022 - 05:03:22 Mar 11, 2022 - 05:03:00 Mar 11, 2022 - 03:03:32 Feb 08, 2022 - 05:02:13
Newer

Stage 01: Hotend Assembly

Written By: Makertech 3D
  • Comments: 35
  • Favorites: 0
  • Completions: 4

Difficulty

Moderate

Steps

3

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

  1. Use two M2.5 x 6mm bolts to fix the servo onto the backplate. Make sure that the servo shaft is centrally aligned with the backplate.

    • Use two M2.5 x 6mm bolts to fix the servo onto the backplate.

    • Make sure that the servo shaft is centrally aligned with the backplate.

  2. Insert an M5 x 20mm bolt with a needle bearing and shim. M5 x 20mm Bolt

    • Insert an M5 x 20mm bolt with a needle bearing and shim.

    • M5 x 20mm Bolt

    • Thrust Bearing

    • Shim

    • On the other side of the heatsink slide on another thrust bearing.

  3. Begin by preparing the backplate with two M3 x 8mm bolts as shown. Drop an M5 nut into the back of the Backplate. Fix the assembly together, making sure that there is no play in the switching motion.

    • Begin by preparing the backplate with two M3 x 8mm bolts as shown.

    • Drop an M5 nut into the back of the Backplate.

    • Fix the assembly together, making sure that there is no play in the switching motion.

    • The bolt should be tightened down enough to allow the heatsink to rock, but there shouldn't be any play along the axis of rotation or on the plane of contact.

Author

Makertech 3D

Member since: 3/9/18

51,265 Reputation

137 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 3

All Time: 1,219