You're viewing a previously published revision of this guide.  View latest revision

Older
May 10, 2020 - 08:05:00
Oct 07, 2020 - 05:10:08 Sep 28, 2020 - 09:09:46 Sep 07, 2020 - 03:09:56 Aug 11, 2020 - 04:08:52 Aug 11, 2020 - 04:08:46 Aug 11, 2020 - 04:08:38 Aug 11, 2020 - 04:08:22 Aug 11, 2020 - 04:08:28 Aug 03, 2020 - 06:08:08 Jul 05, 2020 - 07:07:03 Jul 05, 2020 - 06:07:02 Jul 05, 2020 - 06:07:52 Jul 05, 2020 - 06:07:32 Jul 05, 2020 - 06:07:40 Jun 18, 2020 - 04:06:36 Jun 18, 2020 - 04:06:24 Jun 18, 2020 - 04:06:53 Jun 18, 2020 - 04:06:18 Jun 18, 2020 - 04:06:59 Jun 18, 2020 - 04:06:14 Jun 18, 2020 - 04:06:35 Jun 18, 2020 - 04:06:24 Jun 18, 2020 - 04:06:45 Jun 18, 2020 - 04:06:44 May 28, 2020 - 07:05:23 May 16, 2020 - 07:05:00 May 13, 2020 - 07:05:07 May 13, 2020 - 07:05:26 May 11, 2020 - 10:05:58 May 11, 2020 - 10:05:36 May 11, 2020 - 10:05:03 May 11, 2020 - 10:05:49 May 11, 2020 - 10:05:01 May 11, 2020 - 10:05:57 May 11, 2020 - 10:05:29 May 11, 2020 - 10:05:20 May 11, 2020 - 10:05:54 May 11, 2020 - 10:05:59 May 11, 2020 - 10:05:32 May 11, 2020 - 10:05:20 May 11, 2020 - 10:05:26 May 11, 2020 - 10:05:36 May 11, 2020 - 10:05:47 May 11, 2020 - 10:05:00 May 11, 2020 - 10:05:29 May 11, 2020 - 10:05:25 May 11, 2020 - 09:05:48 May 11, 2020 - 07:05:07 May 11, 2020 - 06:05:50 May 11, 2020 - 06:05:34 May 11, 2020 - 06:05:36 May 11, 2020 - 06:05:20 May 10, 2020 - 09:05:45 May 10, 2020 - 08:05:00 May 10, 2020 - 08:05:32 May 10, 2020 - 08:05:29 May 10, 2020 - 08:05:33 May 10, 2020 - 08:05:33 May 10, 2020 - 08:05:56 May 10, 2020 - 07:05:04 May 10, 2020 - 07:05:32 May 10, 2020 - 07:05:09
Newer

Stage 8: Wiring

Written By: Makertech 3D
  • Comments: 32
  • Favorites: 0
  • Completions: 18

Difficulty

Moderate

Steps

5

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

  1. Cut 70CM of the braided cable sleeving.

    • Cut 70CM of the braided cable sleeving.

    • Use a lighter to melt the ends to prevent fraying.

  2. Take two 1m motor cables. Thread the sleaving over both of them.

    • Take two 1m motor cables.

    • Thread the sleaving over both of them.

    • Plug one of the cables into the extruder motor.

    • Cable tie that cable to the spool holder bracket.

    • Note, the second cable is there for the dual extrusion upgrade, it is installed now even if you don't have that upgrade.

  3. Turn the lead screw to bring the gantry all of the way down, the hotend should be touching the print surface. Cable tie both bunches of cables together to the gantry.

    • Turn the lead screw to bring the gantry all of the way down, the hotend should be touching the print surface.

    • Cable tie both bunches of cables together to the gantry.

  4. Cut 45CM of the braided cable sleeving.

    • Cut 45CM of the braided cable sleeving.

    • Use a lighter to melt the ends to prevent fraying.

  5. Raise the gantry to the very top. Plug a 1M motor cable into the y-motor. Slide the 45CM cable sleeving over the motor cable and Y-endstop.

    • Raise the gantry to the very top.

    • Plug a 1M motor cable into the y-motor.

    • Slide the 45CM cable sleeving over the motor cable and Y-endstop.

    • Cable tie to the bottom of the gantry.

Author

Makertech 3D

Member since: 3/9/18

51,265 Reputation

137 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 4

Past 30 Days: 14

All Time: 2,055