You're viewing a previously published revision of this guide.  View latest revision

Older
May 20, 2024 - 07:05:17
Jul 31, 2024 - 05:07:12 Jul 31, 2024 - 05:07:56 Jul 31, 2024 - 05:07:54 Jun 12, 2024 - 06:06:37 Jun 12, 2024 - 06:06:58 May 23, 2024 - 04:05:34 May 23, 2024 - 04:05:21 May 22, 2024 - 09:05:04 May 22, 2024 - 08:05:09 May 22, 2024 - 08:05:28 May 22, 2024 - 08:05:38 May 22, 2024 - 08:05:17 May 22, 2024 - 08:05:34 May 22, 2024 - 08:05:54 May 22, 2024 - 08:05:08 May 22, 2024 - 08:05:43 May 22, 2024 - 08:05:05 May 22, 2024 - 08:05:40 May 22, 2024 - 08:05:09 May 22, 2024 - 08:05:37 May 22, 2024 - 08:05:39 May 22, 2024 - 08:05:50 May 22, 2024 - 07:05:19 May 22, 2024 - 07:05:12 May 22, 2024 - 07:05:15 May 22, 2024 - 07:05:03 May 21, 2024 - 07:05:12 May 21, 2024 - 04:05:38 May 21, 2024 - 04:05:33 May 21, 2024 - 03:05:38 May 20, 2024 - 10:05:18 May 20, 2024 - 10:05:57 May 20, 2024 - 10:05:23 May 20, 2024 - 10:05:17 May 20, 2024 - 10:05:20 May 20, 2024 - 10:05:36 May 20, 2024 - 07:05:46 May 20, 2024 - 07:05:31 May 20, 2024 - 07:05:09 May 20, 2024 - 07:05:09 May 20, 2024 - 07:05:44 May 20, 2024 - 07:05:40 May 20, 2024 - 07:05:31 May 20, 2024 - 07:05:17 May 20, 2024 - 06:05:29 May 20, 2024 - 06:05:01 May 20, 2024 - 06:05:09 May 20, 2024 - 06:05:45 May 20, 2024 - 06:05:19 May 20, 2024 - 06:05:44 May 20, 2024 - 06:05:40 May 20, 2024 - 06:05:12
Newer

Stage 09: Auto-Calibration

Written By: Makertech 3D
  • Comments: 13
  • Favorites: 0
  • Completions: 2

Difficulty

Moderate

Steps

5

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

    • Check your probe assembly:

    • Check you're able to press the stainless steel ball to trigger the switch.

    • Check that the bolts holding the switch in place are secure.

    • Run the cable for the probe down to the base through the beds cable loom.

    • The 4-pin header side of the cable should go into the base.

    • Plug the 4-pin header into the Octopus Max board.

    • Cut the magnetic base to gain access to the mounting hole for the probe.

    • Fix the probe to the platform with the included M5x20mm bolt.

    • Plug the cable into the probe.

    • Use Termius to copy the tools_calibrate.py file into the ~/klipper/Klippy/Extras folder.

    • Add the calibrate-offsets.cfg file to your config files folder.

    • If you haven't already we also recommend updating your printers other config files also.

Author

Makertech 3D

Member since: 3/9/18

51,265 Reputation

137 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 5

Past 30 Days: 16

All Time: 1,010