You're viewing a previously published revision of this guide.  View latest revision

Older
May 29, 2020 - 09:05:47
Aug 24, 2020 - 06:08:18 Jul 11, 2020 - 09:07:14 Jul 11, 2020 - 09:07:54 Jul 11, 2020 - 09:07:05 Jul 11, 2020 - 09:07:48 Jul 11, 2020 - 09:07:58 Jul 11, 2020 - 09:07:31 Jul 11, 2020 - 09:07:50 Jul 11, 2020 - 09:07:15 Jul 11, 2020 - 09:07:32 Jul 07, 2020 - 02:07:27 Jul 07, 2020 - 12:07:49 Jun 13, 2020 - 09:06:31 Jun 13, 2020 - 09:06:20 Jun 13, 2020 - 09:06:38 Jun 13, 2020 - 09:06:11 Jun 13, 2020 - 09:06:34 Jun 03, 2020 - 08:06:01 Jun 03, 2020 - 08:06:52 Jun 02, 2020 - 06:06:58 Jun 02, 2020 - 06:06:09 Jun 02, 2020 - 06:06:14 Jun 02, 2020 - 05:06:55 Jun 02, 2020 - 05:06:53 Jun 02, 2020 - 05:06:26 Jun 02, 2020 - 04:06:12 May 29, 2020 - 10:05:41 May 29, 2020 - 10:05:31 May 29, 2020 - 10:05:04 May 29, 2020 - 10:05:53 May 29, 2020 - 09:05:32 May 29, 2020 - 09:05:09 May 29, 2020 - 09:05:09 May 29, 2020 - 09:05:18 May 29, 2020 - 09:05:43 May 29, 2020 - 09:05:44 May 29, 2020 - 09:05:47 May 29, 2020 - 09:05:47 May 29, 2020 - 09:05:59 May 29, 2020 - 08:05:24 May 29, 2020 - 08:05:48 May 29, 2020 - 08:05:04 May 29, 2020 - 08:05:37 May 29, 2020 - 08:05:06 May 29, 2020 - 08:05:29 May 29, 2020 - 08:05:22 May 29, 2020 - 08:05:30 May 25, 2020 - 06:05:50
Newer

Stage 10: First Print

Written By: Makertech 3D (and one other contributor)
  • Comments: 21
  • Favorites: 0
  • Completions: 3

Difficulty

Easy

Steps

4

Time Required

00:10:00 - 00:20:00

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

    • Download the latest version of Cura here.

    • Run through the setup wizard and install it onto your computer.

    • Also download the benchy test print, this will be your first print and at the same time will test that the printer can safely print all of its geometries.

  2. Open up the Cura application. Run through the startup wizard.

    • Open up the Cura application.

    • Run through the startup wizard.

    • Click on "add a non-networked printer"

    • Scroll down to Makertech and select the AXIS 3d printer.

    • Then hit next.

  3. Here these setting will vary depending on your setup.

    • Here these setting will vary depending on your setup.

    • If you have a heated bed installed, check this box.

    • If you have dual extruders set-up, set number of extruders to 2.

    • Finally hit next and then finish.

  4. Click on the open file icon.

    • Click on the open file icon.

    • Navigate to and open the Benchy.stl file.

Author

with 1 other contributor

Makertech 3D

Member since: 3/9/18

51,265 Reputation

137 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 4

All Time: 1,362