You're viewing a previously published revision of this guide.  View latest revision

Older
Sep 29, 2023 - 06:09:04
Dec 27, 2024 - 10:12:23 Jan 31, 2024 - 03:01:34 Dec 27, 2023 - 09:12:08 Dec 20, 2023 - 06:12:57 Oct 03, 2023 - 07:10:16 Oct 03, 2023 - 07:10:14 Oct 03, 2023 - 07:10:56 Oct 03, 2023 - 07:10:01 Oct 03, 2023 - 07:10:16 Oct 03, 2023 - 07:10:54 Oct 03, 2023 - 07:10:46 Oct 03, 2023 - 07:10:52 Oct 03, 2023 - 07:10:55 Oct 03, 2023 - 07:10:27 Oct 03, 2023 - 07:10:17 Oct 03, 2023 - 07:10:54 Oct 03, 2023 - 07:10:59 Oct 03, 2023 - 07:10:26 Oct 03, 2023 - 07:10:52 Oct 03, 2023 - 07:10:02 Oct 03, 2023 - 07:10:04 Oct 03, 2023 - 07:10:39 Oct 03, 2023 - 07:10:01 Sep 29, 2023 - 11:09:51 Sep 29, 2023 - 07:09:57 Sep 29, 2023 - 07:09:18 Sep 29, 2023 - 07:09:17 Sep 29, 2023 - 07:09:02 Sep 29, 2023 - 06:09:13 Sep 29, 2023 - 06:09:14 Sep 29, 2023 - 06:09:08 Sep 29, 2023 - 06:09:31 Sep 29, 2023 - 06:09:00 Sep 29, 2023 - 06:09:55 Sep 29, 2023 - 06:09:16 Sep 29, 2023 - 06:09:45 Sep 29, 2023 - 06:09:31 Sep 29, 2023 - 06:09:53 Sep 29, 2023 - 06:09:33 Sep 29, 2023 - 06:09:46 Sep 29, 2023 - 06:09:28 Sep 29, 2023 - 06:09:30 Sep 29, 2023 - 06:09:20 Sep 29, 2023 - 06:09:55 Sep 29, 2023 - 06:09:04 Sep 29, 2023 - 06:09:28 Sep 29, 2023 - 06:09:53 Sep 29, 2023 - 06:09:01 Sep 29, 2023 - 06:09:01 Sep 29, 2023 - 06:09:30 Sep 29, 2023 - 06:09:09 Sep 29, 2023 - 06:09:05 Sep 29, 2023 - 06:09:04 Sep 29, 2023 - 05:09:44 Sep 29, 2023 - 05:09:31 Sep 29, 2023 - 05:09:39 Sep 29, 2023 - 05:09:05 Sep 29, 2023 - 05:09:23 Sep 29, 2023 - 05:09:36 Sep 29, 2023 - 05:09:36 Sep 29, 2023 - 05:09:57 Sep 29, 2023 - 05:09:26 Sep 29, 2023 - 05:09:15 Sep 29, 2023 - 05:09:01 Sep 29, 2023 - 05:09:40 Sep 28, 2023 - 11:09:13 Sep 28, 2023 - 11:09:41
Newer

Upgrade: Enclosure

Written By: Makertech 3D (and one other contributor)
  • Comments: 11
  • Favorites: 0
  • Completions: 6

Difficulty

Easy

Steps

11

Time Required

00:30:00 - 00:45:00

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

Quiz

0

  1. Take the left panel and remove the protective film from it. Prepare the panel by loosely adding onto it fasteners. M4 x 8mm Bolt

    • Take the left panel and remove the protective film from it.

    • Prepare the panel by loosely adding onto it fasteners.

    • M4 x 8mm Bolt

    • M4 T-nut

    • Match the orientation as shown in the diagram about which side the bolts and nuts should be on.

  2. Install the panel to the left side of the frame by sliding it in from the front of the printer. Install the panel to the left side of the frame by sliding it in from the front of the printer.

    • Install the panel to the left side of the frame by sliding it in from the front of the printer.

  3. Take the right panel and remove the protective film from it. Prepare the panel by loosely adding onto it fasteners. M4 x 8mm Bolt

    • Take the right panel and remove the protective film from it.

    • Prepare the panel by loosely adding onto it fasteners.

    • M4 x 8mm Bolt

    • M4 T-nut

    • Match the orientation as shown in the diagram about which side the bolts and nuts should be on.

  4. Install the panel to the right side of the frame.

    • Install the panel to the right side of the frame.

  5. Take the rear panel and remove the protective film from it. Take the 70mm blower fan and fix it to the panel. M4 x 40mm

    • Take the rear panel and remove the protective film from it.

    • Take the 70mm blower fan and fix it to the panel.

    • M4 x 40mm

    • M4 Nyloc Nut

    • Make sure to install the fan on the side shown in the diagram.

  6. Install the 3d printer fume filter fan shroud. M4 x 40mm Bolt

    • Install the 3d printer fume filter fan shroud.

    • M4 x 40mm Bolt

    • M4 Nyloc Nut

  7. Prepare the panel by loosely adding onto it fasteners. M4 x 8mm Bolt

    • Prepare the panel by loosely adding onto it fasteners.

    • M4 x 8mm Bolt

    • M4 T-nut

  8. Install the rear panel as shown to the back of the printer. Install the rear panel as shown to the back of the printer.

    • Install the rear panel as shown to the back of the printer.

  9. Prepare four 3d printed door handles: 3D printed Door Handle

    • Prepare four 3d printed door handles:

    • 3D printed Door Handle

    • M3x10x2mm Countersunk Magnet

    • M3 x 8 CS bolt

    • Self tap the bolt into the 3d printed part.

  10. Take the two front door panels and remove the protective film from both of them. Fix onto both door panels two handle assemblies as shown. M3 x 10mm Bolt

    • Take the two front door panels and remove the protective film from both of them.

    • Fix onto both door panels two handle assemblies as shown.

    • M3 x 10mm Bolt

    • Self tap the bolt into the 3d printed part.

  11. Fix two hinges onto each door panel as shown. The hinges should be installed on the front side of the panel. Hinge

    • Fix two hinges onto each door panel as shown. The hinges should be installed on the front side of the panel.

    • Hinge

    • M4 x 10mm Bolt

    • M4 x 8mm Bolt

    • M4 Nyloc Nut

    • M4 T-nut

    • Fasten these on loosely.

Author

with 1 other contributor

Makertech 3D

Member since: 3/9/18

51,265 Reputation

137 Guides authored

View Statistics:

Past 24 Hours: 0

Past 7 Days: 1

Past 30 Days: 7

All Time: 1,384